Mercedes-Benz G-Model (LWR)

19,00  419,00  incl. 19% VAT

149,00  incl. 19% VAT
239,00  incl. 19% VAT
19,00  incl. 19% VAT

13 in stock

419,00  incl. 19% VAT

76 in stock

Description

The G-Class (or G-model; G stands for off-road vehicle) is a model series from Mercedes-Benz that has been produced since 1979. In its basic form, the vehicle has hardly been changed since then, but technically it has been continuously improved and updated. The G-Class essentially built three body variants for civil use: a two-door convertible, a closed three-door (short station) and a five-door long version (long station).


In den Warenkorb
Preis: 149 €

The G-Class (or G-model; G stands for off-road vehicle) is a model series from Mercedes-Benz that has been produced since 1979. In its basic form, the vehicle has hardly been changed since then, but technically it has been continuously improved and updated. The G-Class essentially built three body variants for civil use: a two-door convertible, a closed three-door (short station) and a five-door long version (long station).


New conversion kit C.HEL.24N.RSMLSTD

Ready-made electrical LWR conversion kit as a replacement for the hydraulic headlight range control for 12 volt vehicles, consisting of:

  • 2 new servomotors
  • 1 new round LWR switch for the interior
  • very detailed illustrated installation instructions
  • Various installation materials
  • 1 cable set (new and suitably assembled)

In den Warenkorb
Preis: 239 €
The G-Class (or G-model; G stands for off-road vehicle) is a model series from Mercedes-Benz that has been produced since 1979. In its basic form, the vehicle has hardly been changed since then, but technically it has been continuously improved and updated. The G-Class essentially built three body variants for civil use: a two-door convertible, a closed three-door (short station) and a five-door long version (long station).
New conversion kit C.HEL.24N.RSOL-24 Ready-made electrical LWR conversion kit as a replacement for the hydraulic headlight range control for 24 volt vehicles, consisting of:
  • 2 new 24 volt actuators
  • 1 new round LWR switch (24 volts) for the interior
  • very detailed illustrated installation instructions
  • Various installation materials
  • 1 cable set (new and suitably assembled)

In den Warenkorb
Preis: 19 €

Voltage converter DC-DC 24 V / 36 V / 48 V to 12 V 3A 36 watts

The voltage converter / voltage converter converts voltage from 24 volts / 36 volts / 48 volts to approx. 13.8 volts (for 12 volt devices), at max. 3 A power around. With this module, 12 volt devices can be operated on a 24 volt battery.

Specification

  • Epoxy sealed waterproof case
  • Input voltage 24 to 48 volts
  • Output voltage 12 volts
  • Output current 3A
  • continuous output power 36W
  • Conversion efficiency 96%
  • Surge protection Yes
  • Low voltage protection Yes
  • Over temperature protection Yes
  • Power cable approx.15cm
  • Operating temperature approx. -40 to +85 degrees
  • Wire color red / black for input - yellow / black for output

In den Warenkorb
Preis: 419 €
[vc_row][vc_column][vc_column_text]
Conversion to electric automatic LWR – headlight range control for various vehicles This conversion kit is among other things required for imported vehicles or for retrofitting LED or xenon headlights. Until around the end of 2018, Hella provided a universal aLWR retrofit kit (8XX 010 315-001), which unfortunately is no longer manufactured and sold by Hella. As the demand for an automatic headlight range control still is very large I decided to develop an ALWR myself. This ALWR (automatic headlight range control) is specially designed for vehicles with xenon or LED headlights, in which the light source of a headlight has a target luminous flux of 2000 Lumens exceeds. According to the legislator, these vehicles no longer allow the headlight range to be regulated manually from the interior. This ALWR retrofit is mostly used for vehicles imported from abroad that do not have the appropriate automatic headlight range control were delivered and are therefore not eligible for approval in Germany without adjustment. Corresponding servomotors must of course be able to be mounted on the headlamp.
  • Somewhere on the back of the headlamp there should be a knob that can be used to manually adjust the headlamp beam by turning it. If you remove this knob, an LWR servomotor should be used in the same place instead so that the control can then be carried out electrically. After removing the manual adjustment, the “installation hole” should look like the last picture with the 3 recesses arranged in a circle.
You should therefore contact me before buying and send a few good photos from the back of the headlight and the removed manual adjuster on the headlight by email!
  • It should also be noted that the function of the ultrasonic sensor is only guaranteed in the range from 22 cm to 100 cm, so the vehicle should be within this range with its ground clearance.
The installation and subsequent calibration of the electronics is very simple and can also be done by an inexperienced layperson, provided you have a current tester and can handle it. Functionality: The automatic headlight range control automatically regulates the angle of inclination in all loading conditions. to create a constant light range and not to dazzle oncoming traffic. The ultrasonic sensor used is attached at the level of the rear axle and provides the electronics I have developed with corresponding pulses over the distance to the road, so that the electronics then regulate the servomotors and thus the headlight range accordingly. After successful calibration of the LWR, the saved setting values are retained even when the battery is disconnected.
Calibration: The calibration is kept extremely simple. The headlights are adjusted using the “Up” / “Down” buttons and then the correct setting is saved by pressing “Save”. Important NOTE: The retrofitting of the vehicle is subject to registration (TÜV / DEKRA or similar) Scope of delivery:
  • 1 electronic control (interface)
  • 1 ultrasonic sensor
  • 2 Hella servomotors
  • Illustrated detailed installation instructions
  • Ready-made cable set with assembled
  • confusion-proof plugs From that:
    • 5m supply line to the ultrasonic sensor
    • 2.5 m supply cable for driver side driver
    • 2.1 m power cable from driver’s side to passenger’s side
    • 0.2 m power connection (ground and 12 volts)
This aLWR installation kit contains everything you need for the conversion. The installation time is about 2 to 3 hours.[/vc_column_text][vc_column_text css=".vc_custom_1597658324862{margin-bottom: 0px !important;}"]Vehicles converted so far:[/vc_column_text][vc_row_inner][vc_column_inner width="1/2"][vc_column_text css=".vc_custom_1601301119790{margin-bottom: 0px !important;}"]BMW - E32 Chrysler - Pacifica Dodge - Durango Dodge - Challenger Ford - Ranger Limited Hymer - Camper Mazda - CX9 Mercedes Benz - G-Modell[/vc_column_text][/vc_column_inner][vc_column_inner width="1/2"][vc_column_text css=".vc_custom_1601301139315{margin-bottom: 0px !important;}"]Mercedes Benz - SL R129 Mercedes Benz - SL R230 Porsche - 996 - 997 Toyota - Sienna VW T4 - ProjectZwo VW T5 - ProjectZwo VW T6 - ProjectZwo Yamaha - XT1200Z[/vc_column_text][/vc_column_inner][/vc_row_inner][/vc_column][/vc_row]

Additional information

Weight 0,3 kg